Versions Compared

Version Old Version 5 New Version Current
Changes made by

Michael.Brumbaugh

Ivana Srebrenova

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Scroll ignore
Scroll ignore
Article statuskb-articleINLINE

Greenexternal

Link to be provided outside of Bosch

kb-articleINLINE

Yellowinternal

Internal document. This article cannot be provided outside of Bosch.




SYMPTOMS:

  1. The Dashboard has a Maximum temperature that exceeds 80 Degrees C.
    1. The Diagnostic log will also report this as the "Highest Temperature", will increase the "Exceed high temperature" counter by the amount of times that the internal temperature exceeded 80 Deg C, and will track the hours/minutes that it exceeded 80 Deg C as " Device temp max period".
  2. The camera will display "Status 8" when the internal temperature is above 80 Deg C.

Possible causes and solution(s)

  • Causes

As part of QMM routine monitoring of field returns, a potential overheating issue for the AUTODOME IP inteox 7000i cameras was observed.

A malfunction in one of the software components controlling the camera's heater was identified on the version 8.12.0005. The malfunction only occurs when the camera is exposed to specific conditions. To eliminate any inconvenience to our customers, FW 8.12.0010 fixes this malfunction. It is available on the Bosch Security Download Store.

  • Solution

The camera FW must be upgraded. to 8.12.0010 or higher.

Do not  connect the AUTODOME inteox 7000i camera to the network and configure it while it is still inside the packaging/box.


PLEASE do not set "ad" label from beginning. Use it only when you need this info and REMOVE the "ad" label when finished!

Information below is for CTS, SG, GK reference and must be kept internal only

NOTE: FW version 8.12.0010, is a prerequisite for the process of upgrading to firmware versions 8.40.00029 or higher.

Scroll ignoreadvancedINLINEgreenINLINE

MANDATORY --> after finishing this article, if you wrote advanced content in this section , you must to manually add the "advanced" label  This action is required to indicate that this article contains ADVANCED instructions for CTS/ SG or GK.

DO NOT CHANGE ANYTHING IN THIS SECTION!

advanced section
Please contact CTS / SG or GK team to view this section from draft space, if necessaryadINLINE

IMPORTANT! --> the content itself from here will be not displayed. The content from here will be displayed only when the "ad" label will be set after article creation. Only CTS/ SG or GK are allowed to use "ad" label.

.

If you are part of CTS, SG or GK team, please hide this section when you have finished using this article!

DO NOT CHANGE ANYTHING IN THIS SECTION!

This section will not be published externally and / or automatically downloaded in the PDF file!

Type your text/ advanced information here

Please note that one customer in NA operated cameras with the FW bug (8.12.0005) inside the packaging that the camera is shipped in. The internal temperature increased high enough over 24 hours to warp the bubble. But the external surfaces did not exceed the UL safety limits and there was not any risk of fire.

Per internal agreement, any customer that reports a deformed bubble can receive a replacement bubble free of charge. The RMA desk can be contacted so that that they can process the request.  

Add pictures, if necessary





Scroll only
scroll-pdftrue
scroll-officetrue
scroll-chmtrue
scroll-docbooktrue
scroll-eclipsehelptrue
scroll-epubtrue
scroll-htmltrue


You are using an Offline Version of these Article, please ensure to regularly check the corresponding online article on the Bosch Building Technologies Knowledge Base for any updates. Use the date and version information of the document as reference.

This is  created  

Check for Updateprimaryhttps://community.boschsecurity.com/t5/Bosch-Building-Technologies/ct-p/bt_community